VFD Control Panels Built in Houston, Texas

WETS AI builds custom VFD control panels in Houston for pumps, blowers, fans and process motors. We size the drive, its protection and its cooling, build the panel to UL 508A, and record every drive setting during testing so your team knows exactly how the panel left our shop.

What Goes Into a VFD Panel

A variable frequency drive controls motor speed by changing the frequency and voltage it supplies. The panel around it protects the drive, keeps it cool, and connects it safely to the rest of your control system.

  • Variable frequency drive
  • Disconnect and short-circuit protection
  • Line reactor or harmonic filter
  • Load reactor or output filter
  • Bypass contactors, when needed
  • Fans or air conditioning
  • Control relays and PLC interface
  • Door-mounted keypad or HMI
Variable frequency drives mounted for motor speed control
Variable frequency drives mounted for motor speed control
Illustration of a VFD control panel backplate: a rotary disconnect, fuses and a control transformer on top, a line reactor next to the variable frequency drive with its keypad display and heat sink in the middle, bypass contactors with overload relays and control relays below, and motor and control terminals at the bottom.

Heat Is the Main Design Problem

Drives turn a few percent of the power they handle into heat, and that heat has to leave the enclosure. A drive that runs hot trips, derates, or fails early.

Indoor NEMA 1 panels can often use filtered fans. Sealed NEMA 3R, 4 and 4X panels outdoors in Texas also pick up heat from the sun, so they usually need closed-loop air conditioning or a heat exchanger. We work out the heat load for each panel and choose the cooling to match, instead of guessing.

Bypass, Harmonics and Long Motor Leads

A bypass lets the motor run directly on line power if the drive fails. It is useful for pumps that must keep running, but only where the process can tolerate full speed.

Line reactors and harmonic filters reduce the distortion a drive sends back onto your supply, which some utilities and plants require. Where the motor is far from the panel, a load reactor or output filter protects the motor insulation from voltage spikes.

From Supply to Motor

Power passes through protection and conditioning before it reaches the drive, then on to the motor.

  • Fuses or a breaker protect the drive and help set the panel SCCR
  • A line reactor reduces harmonics and softens supply spikes
  • An output filter protects motor insulation on long cable runs
  • A bypass keeps critical motors running if the drive is out of service
Power path in a VFD panel: incoming supply, disconnect and short-circuit protection, line reactor or harmonic filter, the variable frequency drive, and a load reactor or output filter to the motor.

Choosing How to Cool a VFD Panel

Drives give off heat, and heat shortens drive life.

How we remove it depends on where the panel will live: indoors or out, clean air or dusty, shade or full Texas sun.

OptionSuitsKeep in mind
Filtered fansIndoor NEMA 1 panels in clean, cool roomsSimplest option, but it brings room air and dust into the panel
Air-to-air heat exchangerSealed panels with moderate heat loadsKeeps outside air out, but cannot cool below the outside temperature
Closed-loop air conditionerSealed outdoor panels in hot climatesCools below ambient; needs a condensate drain and routine maintenance

We size the option from the calculated heat load and the site conditions, including direct sun on outdoor panels.

How We Test a VFD Panel

01

Check the build

Wiring, ratings and torque are checked against the drawings.

02

Power up

Incoming voltage, phase rotation and control power are verified.

03

Set and record

Drive parameters are entered and recorded for your files.

04

Run the functions

Start, stop, speed reference, faults and bypass transfer are tested.

Where Our VFD Panels Work

Typical loads our VFD panels drive.

  • Pumps and lift stations
  • Aeration blowers
  • Cooling tower fans
  • Combustion air fans
  • Mixers and agitators
  • Conveyors

VFD Panel Questions

Can you build a VFD panel with a bypass?

Yes. We build bypass panels with interlocked contactors, so the motor can run on line power if the drive is out of service.

Do you set up the drive parameters?

Yes. We enter and record the drive settings during testing. Final tuning against the real load is done on site at SAT.

Which drive brands do you use?

Allen-Bradley, Siemens and Schneider Electric drives, normally matching the PLC platform and the spares your plant already keeps.

Can a VFD panel go outdoors in Texas?

Yes, in a NEMA 3R, 4 or 4X enclosure with cooling sized for the heat load and the sun. We size it for your site.

What if the motor is a long way from the panel?

Long motor leads can cause voltage spikes at the motor. We add a load reactor or output filter when the cable length calls for it.

Related Panels & Services

PLC Control Panels

Controllers, I/O, networks and power, built to UL 508A and tested point by point.

Need a VFD Panel?

Send the motor list and site conditions, or your drawings. We will size the drive, protection and cooling, and quote the complete panel.

Call Request a Quote